MIL122 – MIL 123

Plate size 1200x1000 MM 47x39inch

MIL 122 - MIL 123

Description

On the traditional MIL/Classic series spotting presses, the extractable plate comes out of the side wall, on the short side between the columns. Typical application is in the classic fields of plastic, rubber, and die-casting. This solution makes it possible to tip the extractable plate on the short side by up to 70° on both sides. In this version the upper plate can also tip along the short side from 100° to 150°/180°.

The advantages of the MIL CLASSIC presses:

Standard equipment

Multi Panel Touch panel
Millutensil is the first manufacturer in the world to have incorporated touch panels in their spotting presses. All of the machine's functions are controlled by a Siemens S7 - 300 PLC.

The machine is fitted with a latest - generation Siemens TP1200 Multi Panel touch panel. Uncluttered, clear and ergonomic, the panel offers many advantages as well as vast flexibility in customizing features, including control of the auxiliary cylinders.

Touch panel Multipanel


Hydromechanical Fall Arrestors For The Upper Plate
Two hydromechanical fall arrestors on the right and left sides of the upper plate of the press act for the entire length of travel. The patented device (SITEMA) immediately stops and locks the plate in the event of a loss of hydraulic pressure. Unlike conventional perforated or toothed bars, this system avoids all falls of the ram of the press in the event of a hydraulic failure.

Dispositivi anticaduta idromeccanici contro la caduta del piano superiore

Floor version

MIL 122 - MIL 123 - FLOOR


MIL 122 - MIL 123 - TILTING OPTIONS

150° Tilting Press Upper Plate
During the first phase, the upper plate of the press tilts by up to 100°. Subsequently, with the down-stroke movement, the press plate rests and slides on the 2 shaped brackets up to the final ~150° position. It can be stopped in all intermediate positions. After complete closure, the press plate is automatically centred with high precision and locked by a system operated by hydraulic cylinders.

PIANO SUPERIORE DELLA PRESSA RIBALTABILE DI 150°

Lower Plate Of Press Tilts By ±70°, Front/Back
Thanks to 2 hydraulic cylinders, the lower plate can be tilted up to 70°, on the front and back side, to bring the mould to an ergonomically better position. The tilting movements (and automatic locking) are controlled by means of the touch panel.

RIBALTAMENTO DEL PIANO INFERIORE DELLA PRESSA DI ±70° LATO ANTERIORE / POSTERIORE

ALSO AVAILABLE IN LIMITED EDITION VERSION

Video

Accessories

ELECTRONIC UPPER PLATE PARALLELISM ANTI-UNBALANCE SAFETY DEVICE
The control system includes 4 electronic measurement devices (encoders), which continuously check the upper plate of the press position and parallelism compared to the lower plate and which are located diagonally in the four external corners of the upper plate, near the columns. 

CONTROLLO ELETTRONICO DEL PARALLELISMO DEL PIANO SUPERIORE

The values measured are dynamically displayed on the touch panel for the entire stroke. If the pre-set limit parameters are exceeded, the ram closing movement is immediately disabled and the error is shown on the display. Parameters can be exceeded for example because the slides or hydraulic cylinders are not retracted, or tools were left in the mould (scrapers, grinders, slip gauges, hammers, etc.).

Using this system both the press and the moulds are protected from possible damage.

CONTROLLO ELETTRONICO DEL PARALLELISMO DEL PIANO SUPERIORE

ENERGY ACCUMULATOR (SINGLE SHOT)
For the development of moulds for plastics, rubber and die-casting. It is a hydraulic device which is fixed to the upper plate of the press. It gives an instant blow to the closed mould to optimally check the coupling between the two half-moulds (punch and die). The dynamic action of the device is independent of the closing movement of the press. As a result, the dynamic effect of the energy accumulator is added to the closing force of the press.

ENERGY ACCUMULATOR (SINGLE SHOT)

Special Wax Automatic Injection Unit
This attachment provides a way to inject special wax at a low pressure into the mould cavity. This makes it possible to check, on the basis of the moulded parts obtained, the dimensions and thicknesses of the degree of tightness of the mould, and any burrs and flashes. The wax injection attachment includes: wax container with thermostat-controlled electric heating, pneumatic drive with air pressure control, and a temperature control for the chamber to attain constant wax fluidity.

Unità automatica d’iniezione di cere speciali

HYDRAULIC EJECTOR UNIT
Drives the movement of the extraction pins of moulds for plastics and die-casting.

Unità espulsore idraulico

Integrated Auxiliary Cylinders Control Unit
This hydraulic device allows movement of cylinders applied on the die or mould for greater control of mobile parts (max 2+2).

UNITÀ INTEGRATA DI COMANDO CILINDRI AUSILIARI

Cart For Hydraulic Cylinders (4+4))
Made up of a separate hydraulic power unit interfaced to the press, available with pumps from 8 to 40 litres / min.

CARRELLO PER CILINDRI AUSILIARI IDRAULICI (4+4)

X

Request Pdf

I read and agree to the disclosure in accordance with Legislative Decree no. 196/2003
verification code

Reg. Imp. Milano 08060920157 REA 1200630 - P. Iva 08060920157 | Millutensil S.r.l ©2016 | CREDITS